Home / Length & Area / Mesh to Micron

Specialty

Mesh to Micron Converter

Estimate the opening size in microns for a US sieve mesh number. Mesh and micron are inversely related; the exact opening depends on wire thickness.

Standard values are used where available; otherwise the 15,000 ÷ mesh approximation applies.

Approx. opening size

74 microns

Millimeters—
Inches—
Source—

Standard US sieve reference

MeshMicronsMeshMicrons
102000100149
20840140105
4042020074
6025032544
8017740037

How it works

Mesh is the number of openings per linear inch of a sieve. A higher mesh means more, smaller openings, so mesh and micron size move in opposite directions. Because the opening also depends on the wire diameter, this tool uses standard sieve values where they exist and a simple approximation otherwise.

microns ≈ 15,000 ÷ mesh  (rule of thumb)
1000 microns = 1 mm  ·  25,400 microns = 1 inch

Common mesh sizes and uses

The mesh number counts openings per linear inch, but the actual opening also depends on wire thickness, so sieve standards fix an opening size for each mesh number. The values below are the traditional US sieve openings this calculator uses; the current ASTM E11 standard rounds some of them slightly (for example 75 µm for No. 200).

US sieve meshOpening
20 mesh840 µm (0.84 mm)
40 mesh420 µm (0.42 mm)
60 mesh250 µm (0.25 mm)
100 mesh149 µm (0.149 mm)
140 mesh105 µm (0.105 mm)
200 mesh74 µm (0.074 mm)
325 mesh44 µm (0.044 mm)
400 mesh37 µm (0.037 mm)

Coarse meshes (10 to 40) are used for sand and soil grading, 100 to 200 mesh for fine powders and pigments, and 325 to 400 mesh for very fine powders such as some mineral fillers and cosmetic ingredients. For filters, check whether the rating is nominal or absolute, as that changes what actually passes through.

Particle sizes for comparison

ParticleTypical sizeApprox. mesh
Coarse sand500–1,000 µm18–35
Medium sand250–500 µm35–60
Fine sand125–250 µm60–120
Human hair (width)about 50–100 µm140–270
Pollen grainsabout 10–100 µm140 and finer
Silt4–63 µm230 and finer
Red blood cellabout 7–8 µmbeyond sieve range

Why wire diameter matters

The open space in a screen is the distance between wires, not the full 1/mesh spacing. For woven wire: opening = (1 ÷ mesh) − wire diameter. A 100-mesh screen woven from 0.0045" wire has openings of 0.01 − 0.0045 = 0.0055", about 140 µm. Heavier wire on the same mesh count gives smaller openings, which is why standard sieve tables are used for accurate work.

US sieve vs Tyler mesh

Nominal vs absolute micron ratings

A nominal rating means the filter catches most particles of that size, often 85% to 95%. An absolute rating means it catches essentially all particles at or above that size, typically 99.9% or more. Absolute-rated filters are used where contamination matters, such as hydraulics and drinking water.

Frequently asked questions

How do you convert mesh to microns?

Use a standard sieve table; the rough rule is microns ≈ 15,000 ÷ mesh.

What is 200 mesh in microns?

About 74 microns.

What is 100 mesh in microns?

149 microns (0.149 mm) on the US standard sieve series.

Is a higher mesh number finer?

Yes. More openings per inch means each opening is smaller, so 325 mesh (44 µm) is much finer than 40 mesh (420 µm).

How do I calculate mesh opening size?

Opening (inches) = 1 ÷ mesh count − wire diameter. Multiply inches by 25,400 to get microns.

What mesh size is fine sand?

Fine sand (125 to 250 µm) passes roughly 60 to 120 mesh screens.

Related calculators