Home / Force, Pressure & Torque
Directory
Force, Pressure & Torque Converters
Converters for mechanics, engineers and DIYers: torque wrench specs, tire and hydraulic pressure, force units and engine horsepower. Each page lists the exact factor and real-world reference values.
Pressure converters
Force & power
Torque, pressure and force conversion chart
| From | To | Multiply by |
|---|---|---|
| Newton-meters (Nm) | Foot-pounds (ft-lb) | 0.737562 |
| Foot-pounds | Newton-meters | 1.355818 |
| Inch-pounds (in-lb) | Newton-meters | 0.112985 |
| Foot-pounds | Inch-pounds | 12 |
| psi | bar | 0.0689476 |
| bar | psi | 14.5038 |
| psi | kPa | 6.89476 |
| Standard atmosphere | psi | 14.6959 |
| Pounds-force (lbf) | Newtons (N) | 4.44822 |
Common reference values
- Car lug nuts: typically 80–100 ft-lb (108–136 Nm); check your owner's manual.
- Spark plugs: about 10–20 ft-lb depending on thread size and seat type.
- Passenger car tires: usually 30–35 psi (2.1–2.4 bar); the correct figure is on the door-jamb sticker.
- Road bike tires: 80–120 psi; mountain bike tires: 25–35 psi.
- Sea-level air pressure: 14.7 psi = 1.013 bar = 101.3 kPa = 760 torr.
Torque and horsepower
Horsepower is torque multiplied by engine speed: HP = torque (lb-ft) × RPM ÷ 5,252. That is why torque and horsepower curves always cross at 5,252 RPM on a dyno chart. An engine making 300 lb-ft at 4,000 RPM produces 300 × 4,000 ÷ 5,252 ≈ 228 HP.
Getting torque right in the garage
A torque spec is only as good as the way it is applied. The conversion from Nm to ft-lb is exact, but the clamping force a bolt actually delivers depends on several things the number on the page does not show:
- Dry or lubricated threads. Specs are usually given for clean, dry threads unless the manual says otherwise. Oil or anti-seize reduces friction, so the same torque stretches the bolt further. Some manufacturers specify a reduced torque, often 20% to 25% lower, when anti-seize is used.
- Wrench accuracy. Most click-type torque wrenches are accurate to about ±4% in the middle of their range and less accurate near the ends. Use a wrench whose range puts your target in the middle 20% to 80%.
- Storage. Wind a click wrench back to its lowest setting after use so the spring does not take a set and read high next time.
- Technique. Pull smoothly at a steady rate and stop the moment a click wrench breaks over. Jerking the handle overshoots the setting, and pulling again after the click adds torque.
- Calibration. Torque wrenches drift with use. Professional shops check them yearly or every 5,000 cycles; for home use, have a wrench checked if it has been dropped or is more than a few years old.
Specs arrive in mixed units because manufacturers and tool makers mix them: a European car manual gives Nm, a US wrench may be marked in ft-lb, and small fasteners on bikes and electronics often use in-lb. The Nm to ft-lbs and inch-lbs to Nm converters cover the usual pairs.
Pressure readings change with the weather
Tire pressure is not fixed: it moves with temperature. As a rule of thumb, a tire loses or gains about 1 psi (roughly 7 kPa) for every 10 °F (5.6 °C) change in air temperature. A tire set to 35 psi in a 70 °F garage reads about 31 psi on a 30 °F morning, low enough to trigger a warning light. That is why the door-jamb figure is a cold pressure, to be checked before driving, and why pressures need topping up as autumn turns to winter.
Altitude affects gauge readings too, because gauges measure pressure relative to the surrounding air. Driving from the coast into the mountains raises the gauge reading slightly as the outside air pressure falls. For most drivers the change is small; for pilots, divers and anyone working with sealed systems, the difference between gauge and absolute pressure matters a great deal.
Newtons, pounds-force and kilogram-force
Force is mass times acceleration, so a newton is the force that accelerates 1 kg at 1 m/s². Because Earth's gravity accelerates objects at 9.80665 m/s², a 1 kg mass weighs 9.81 N. That figure is also called one kilogram-force (kgf). A pound-force (lbf) is the weight of a 1 lb mass, or 4.448 N. In practice, a newton is roughly the weight of a small apple. Load ratings on climbing gear are given in kilonewtons. A carabiner rated at 24 kN can hold about 2,450 kgf (5,400 lbf). Shelf brackets, anchors and lifting straps may be rated in kg, lb or N depending on where they were made, so convert to one unit before comparing them. Always use the rating for the way the item will actually be loaded.
Which units you will meet, and where
| Context | US | UK | Canada | Australia |
|---|---|---|---|---|
| Tire pressure | psi | psi and bar | kPa and psi | psi and kPa |
| Fastener torque | ft-lb, in-lb | Nm | Nm and ft-lb | Nm |
| Weather (barometric) | inches of mercury | millibars (hPa) | kPa | hPa |
| Engine power | horsepower | bhp and kW | hp and kW | kW |
For pressure work beyond tires, such as compressors, pressure washers, hydraulics and lab equipment, the pressure conversion page covers psi, bar, kPa, atmospheres, inches of mercury and more in one place, and the psi to bar converter is quickest for the most common pair.
Frequently asked questions
How do I convert Nm to ft-lbs?
Multiply newton-meters by 0.737562. For example, 100 Nm × 0.7376 = 73.8 ft-lb.
How many psi is 1 bar?
About 14.5 psi. One bar is 100 kPa, slightly less than standard atmospheric pressure (1.01325 bar).
What is the difference between in-lbs and ft-lbs?
Both measure torque. A foot-pound is 12 inch-pounds, so divide in-lbs by 12 to get ft-lbs. Small fasteners are usually specified in in-lbs.
Is psi gauge or absolute pressure?
Tire and air-compressor gauges read psig (gauge pressure, relative to the surrounding air). Absolute pressure (psia) adds about 14.7 psi at sea level.