Equivalent torque
Your value in inch-pounds, foot-pounds, and newton-meters.
Home / Force, Pressure & Torque / Inch-lbs to ft-lbs
Torque
Convert inch-pounds (in-lbs) to foot-pounds (ft-lbs) of torque, just divide by 12, with a full equivalents table and a comparison chart.
Result
10 ft-lbs
Equivalent torque
Your value in inch-pounds, foot-pounds, and newton-meters.
Because a foot is 12 inches, a foot-pound is exactly 12 inch-pounds. Converting is a simple divide-by-12 (or multiply by 12 the other way).
A torque of 120 in-lbs equals 120 ÷ 12 = 10 ft-lbs, handy when a spec is quoted in one unit but your wrench uses the other.
Both units measure torque with the same force, one pound, on a lever that is one inch or one foot long. Because a foot is 12 inches, 12 inch-pounds equal 1 foot-pound. Inch-pounds are used for small, easily over-tightened fasteners such as bicycle components, scope rings, electrical terminals and small engine covers; foot-pounds are used for wheel nuts, suspension and engine bolts.
| Inch-pounds | Foot-pounds |
|---|---|
| 12 in-lb | 1 ft-lb |
| 24 in-lb | 2 ft-lb |
| 36 in-lb | 3 ft-lb |
| 48 in-lb | 4 ft-lb |
| 60 in-lb | 5 ft-lb |
| 100 in-lb | 8.33 ft-lb |
| 120 in-lb | 10 ft-lb |
| 180 in-lb | 15 ft-lb |
| 240 in-lb | 20 ft-lb |
| 360 in-lb | 30 ft-lb |
Getting the unit wrong is costly: a 40 in-lb spec tightened to 40 ft-lb is 12 times too tight and can strip threads or crack a part. Most click wrenches that read in ft-lb are inaccurate below about 20% of their range, so for small in-lb specs use an inch-pound wrench or a torque screwdriver.
| Inch-pounds | Foot-pounds | Newton-meters |
|---|---|---|
| 12 | 1.00 | 1.36 |
| 24 | 2.00 | 2.71 |
| 60 | 5.00 | 6.78 |
| 100 | 8.33 | 11.30 |
| 120 | 10.00 | 13.56 |
| 180 | 15.00 | 20.34 |
| 240 | 20.00 | 27.12 |
| 360 | 30.00 | 40.67 |
| Drive size | Typical range | Common jobs |
|---|---|---|
| 1/4 inch | 20–200 in-lb | Bicycles, small engines, interior trim |
| 3/8 inch | 10–80 ft-lb | Spark plugs, valve covers, brake calipers |
| 1/2 inch | 30–250 ft-lb | Lug nuts, suspension, axle nuts |
Pick a wrench where your spec falls in the middle of its range. Most click wrenches are rated accurate to about ±4% between 20% and 100% of full scale.
Divide by 12. For example, 120 in-lbs = 10 ft-lbs.
About 8.33 ft-lbs (100 ÷ 12).
12. Multiply foot-pounds by 12 to get inch-pounds, or divide inch-pounds by 12 to get foot-pounds.
8.33 foot-pounds (100 ÷ 12), which is about 11.3 newton-meters.
Only if the converted value is well inside the wrench's range. A 60 in-lb spec is 5 ft-lb, below the accurate range of most 3/8-inch ft-lb wrenches, so use an inch-pound wrench.
5 foot-pounds (60 ÷ 12), or about 6.78 Nm.