Equivalent torque
Your value in newton-meters, foot-pounds, and inch-pounds.
Home / Force, Pressure & Torque / Nm to ft-lbs
Torque
Convert newton-meters (Nm) to foot-pounds (ft-lbs) of torque instantly, with the exact factor, a full equivalents table, and a comparison chart.
Result
73.76 ft-lbs
Equivalent torque
Your value in newton-meters, foot-pounds, and inch-pounds.
Newton-meters and foot-pounds both measure torque, a force applied at a distance from a pivot. The conversion is a single fixed factor.
A wheel-nut spec of 100 Nm converts to 100 × 0.737562 = 73.76 ft-lbs, so a ft-lb torque wrench should be set to about 74.
Car and motorcycle service manuals from European and Asian makers give torque in newton-meters, while many torque wrenches sold in the US are marked in foot-pounds. One newton-meter is 0.737562 foot-pounds, so a metric spec in Nm is always about three quarters of the same figure in ft-lbs.
| Newton-meters | Foot-pounds |
|---|---|
| 5 Nm | 3.69 ft-lb |
| 10 Nm | 7.38 ft-lb |
| 20 Nm | 14.75 ft-lb |
| 25 Nm | 18.44 ft-lb |
| 40 Nm | 29.5 ft-lb |
| 50 Nm | 36.88 ft-lb |
| 80 Nm | 59 ft-lb |
| 100 Nm | 73.76 ft-lb |
| 120 Nm | 88.51 ft-lb |
| 140 Nm | 103.26 ft-lb |
| 200 Nm | 147.51 ft-lb |
Wheel nuts on passenger cars are commonly specified between about 80 and 140 Nm (roughly 60 to 105 ft-lb); always use the figure for your vehicle. Round to the nearest mark your wrench can set rather than the nearest whole number, and never add torque on top of a spec to be safe.
For the reverse direction, multiply foot-pounds by 1.35582:
| Foot-pounds | Newton-meters |
|---|---|
| 10 ft-lb | 13.6 Nm |
| 20 ft-lb | 27.1 Nm |
| 25 ft-lb | 33.9 Nm |
| 30 ft-lb | 40.7 Nm |
| 40 ft-lb | 54.2 Nm |
| 50 ft-lb | 67.8 Nm |
| 75 ft-lb | 101.7 Nm |
| 100 ft-lb | 135.6 Nm |
| 150 ft-lb | 203.4 Nm |
Strictly, torque is written lb-ft (pound-feet) and work or energy is written ft-lb (foot-pounds). In practice mechanics and wrench makers use both for torque, and the numbers are identical, so 100 lb-ft = 100 ft-lb = 135.6 Nm.
Many modern engines use torque-to-yield bolts with a two-step spec such as "30 Nm + 90°". Tighten to the torque value first, then turn the bolt a further 90 degrees with an angle gauge. Converting the first step to ft-lb is fine (30 Nm ≈ 22 ft-lb), but the angle step stays the same in any unit system. Torque-to-yield bolts usually must be replaced, not reused.
Torque figures on car brochures use the same conversion as torque wrench specs. European, Australian and Asian brochures quote Nm, while US ones quote lb-ft. A turbocharged engine rated at 400 Nm makes about 295 lb-ft. Electric vehicles often post very large numbers, 500 to 700 Nm or more, because their motors deliver full torque from a standstill. E-bike motors are rated the same way: an 85 Nm mid-drive motor produces about 63 lb-ft at the crank.
Torque and power are linked through engine speed. In metric units, power in kilowatts = torque in Nm × rpm ÷ 9,549. So 400 Nm at 4,000 rpm is about 168 kW, or 225 horsepower. The torque to horsepower calculator does the same sum in either unit system.
A torque wrench does not measure what you actually care about, which is how hard the bolt clamps the parts together. Torque is an indirect way of setting that clamp load. Engineers use a simple relationship: torque ≈ 0.2 × clamp force × bolt diameter for a dry steel bolt. Rearranged, an M12 bolt tightened to 80 Nm produces roughly 80 ÷ (0.2 × 0.012 m) = 33,000 N of clamp force, about 7,500 pounds-force.
That 0.2 factor (the "nut factor") changes with the surface. Oil, grease or anti-seize can drop it to about 0.15 or lower, so the same 80 Nm then produces a third more clamp force, enough to stretch a bolt past its limit. Plating, rust and thread-locker change it too. This is why the conversion between Nm and ft-lb is exact but the result is only as good as following the spec's conditions: dry or oiled, new or reused fasteners, and the specified sequence.
For quick mental conversion, Nm × 3/4 gets you within 2% of the ft-lb figure, and ft-lb × 4/3 gets you close to Nm. Some typical values you will meet:
These are illustrations, not specs; always use the figure from the manual for your vehicle or part.
Most torque wrenches are only rated accurate between about 20% and 100% of their scale. A 3/8-inch drive wrench covering 10 to 80 ft-lb (about 14 to 108 Nm) suits most car work other than wheel nuts and axle nuts; a 1/2-inch drive wrench covering 30 to 250 ft-lb (about 40 to 340 Nm) handles those. Dual-scale wrenches show both units, which removes the need to convert, but the secondary scale is often printed in coarser steps, so set the wrench using the scale that matches the spec. For small fasteners under about 10 ft-lb, switch to an inch-pound tool and the inch-lbs to Nm converter.
About 0.73756 ft-lbs. Multiply Nm by 0.737562149.
Multiply by 0.737562149, for example, 100 Nm = 73.76 ft-lbs.
73.76 ft-lbs. Multiply newton-meters by 0.737562.
Multiply by 1.35582. For example, 80 ft-lbs is 108.47 Nm.
About 135.6 Nm (100 × 1.35582).
For torque they are used interchangeably and the numbers are the same. Technically, lb-ft is the torque unit and ft-lb the energy unit.