Home / Force, Pressure & Torque / Inch-lbs to Nm

Torque

Inch-lbs to Nm Converter (and Nm to in-lbs)

Convert inch-pounds (in-lbs) to newton-meters (Nm) of torque instantly, with the exact factor, a full equivalents table, and a quick comparison chart.

Result

11.3 Nm

Equivalent torque

Your value expressed in inch-pounds, foot-pounds, and newton-meters.

How it works

Torque is a twisting force, measured as force times the length of the lever arm. Inch-pounds and newton-meters are two units for the same quantity, so converting between them is a single multiplication.

Nm = inch-pounds × 0.112984829
1 Nm = 8.850746 in-lbs

Worked example

A fastener spec of 100 in-lbs equals 100 × 0.112985 = 11.30 Nm. That is why a small torque wrench marked in Nm reads about 11 for a 100 in-lb spec.

Converting Nm back to inch-pounds

Swap the From and To units above to go the other way. One newton-meter is 8.85075 inch-pounds, the reciprocal of 0.112985. This direction is common when a European or Asian service manual gives torque in Nm but your torque screwdriver is marked in in-lbs, as many small-fastener drivers in the US are.

in-lbs = Nm × 8.85074579
1 in-lb = 0.112984829 Nm · 12 in-lbs = 1 ft-lb

Worked example

A 10 Nm spec is 10 × 8.85075 = 88.5 in-lbs. The same torque in foot-pounds is 88.5 ÷ 12 = 7.4 ft-lbs, which is below the range of most click-type ft-lb wrenches, so an in-lb driver is the right tool.

Inch-pounds to Nm conversion chart

Inch-poundsNewton-metersFoot-pounds
10 in-lb1.13 Nm0.83 ft-lb
20 in-lb2.26 Nm1.67 ft-lb
25 in-lb2.82 Nm2.08 ft-lb
30 in-lb3.39 Nm2.50 ft-lb
40 in-lb4.52 Nm3.33 ft-lb
50 in-lb5.65 Nm4.17 ft-lb
60 in-lb6.78 Nm5.00 ft-lb
75 in-lb8.47 Nm6.25 ft-lb
100 in-lb11.30 Nm8.33 ft-lb
150 in-lb16.95 Nm12.50 ft-lb
200 in-lb22.60 Nm16.67 ft-lb

Where inch-pound and small Nm specs appear

Other small torque units

UnitEquals
1 kgf·cm (kilogram-force centimeter)0.868 in-lb, or 0.0981 Nm
1 cN·m (centinewton-meter)0.0885 in-lb
1 ozf·in (ounce-force inch)0.0625 in-lb, or 0.00706 Nm

Kilogram-force centimeters are still common on hobby servos and some Asian service manuals. For larger torque values, use the Nm to ft-lbs converter.

The costly mix-up: inch-pounds vs foot-pounds

The most expensive torque mistake in a home garage is reading an inch-pound spec as foot-pounds. Because a foot-pound is 12 inch-pounds, the error applies twelve times the intended torque. A transmission pan bolt specified at 100 in-lb (11.3 Nm) tightened to 100 ft-lb receives about 136 Nm, enough to strip aluminium threads, crack a pan or snap the bolt. Small engine, motorcycle and drivetrain manuals mix the two units freely, sometimes on the same page, so check the unit every time, not just the number.

A quick sense check helps: if a small bolt with a 6 mm or 1/4-inch thread has a spec in the hundreds, it is almost certainly inch-pounds. Specs for bolts that small in foot-pounds or Nm are usually in single or low double figures.

Picking the right tool for small torque

Trying to hit 60 in-lb with a 3/8-inch wrench by setting it to 5 ft-lb usually fails: 5 ft-lb sits below the accurate range of most ft-lb wrenches, so the actual torque could be well off. Use a tool whose range puts the target near the middle.

Electrical terminals have torque specs too

Breakers, panel lugs, switches and outlets often print a torque value next to the terminal, usually in in-lb, and some in Nm. Under-tightened connections can loosen with heating and cooling and become a fire risk; over-tightened ones can crush conductors or crack the device. In the US, the National Electrical Code requires terminals with a marked torque value to be tightened with a calibrated torque tool, which is why electricians carry torque screwdrivers marked in in-lb. Convert a Nm marking with this calculator and set the driver accordingly.

Soft materials and thread-locker

Small fasteners frequently thread into aluminium, magnesium, plastic or carbon fibre, which tolerate far less torque than steel. Manufacturers' specs for these parts are deliberately low, and a few extra newton-metres can cause damage that is expensive to repair. If a spec calls for thread-locker, it is normally the torque for the fastener with the compound applied; for anti-seize, some manufacturers specify a lower figure. Where the manual is silent, do not add torque "to be safe": tighten to spec and, for critical parts, recheck after a short period of use.

Quick conversions for common small specs

Bike and optics specs in Nm convert to in-lb by multiplying by 8.85: 4 Nm is about 35 in-lb, 5 Nm about 44 in-lb and 6 Nm about 53 in-lb. Going the other way, divide in-lb by 8.85, or multiply by 0.113.

Frequently asked questions

How many Nm is 1 inch-pound?

About 0.11298 Nm. Multiply inch-pounds by 0.112984829 to get newton-meters.

How do I convert inch-lbs to Nm?

Multiply by 0.112984829. For example, 100 in-lbs = 11.30 Nm.

How many in-lbs is 1 Nm?

About 8.85 in-lbs. Multiply newton-meters by 8.85074579 to get inch-pounds.

What is 25 in-lbs in Nm?

About 2.82 Nm (25 × 0.112985).

How do I convert kgf·cm to in-lbs?

Multiply by 0.868. A 10 kgf·cm servo produces about 8.7 in-lb, or 0.98 Nm.

Related calculators